1998 Ford Contour Recall

FEDERAL MOGUL IS RECALLING 6,903 AFTERMARKET BALL JOINT ASSEMBLIES SHIPPED BETWEEN NOVEMBER 9, 2007 AND MARCH 26, 2008, WHICH MAY HAVE BEEN PACKAGED WITH INCORRECT NUTS. THE PART NUMBERS PACKAGED WITH INCORRECT NUTS ARE: K7147, K7329, K8683, AND 104353. THESE PARTS WERE MADE FOR USE ON THE VARIOUS VEHICLES LISTED ABOVE.

CERTAIN AFTERMARKET BRAKE HYDRAULIC MASTER CYLINDERS SOLD AS REPLACEMENT BRAKE CYLINDERS FOR CERTAIN FORD, DAIMLERCHRYSLER, AND JEEP PASSENGER VEHICLES. THESE BRAKE CYLINDERS WERE SOLD UNDER THE BRAND NAMES OF NAPA, RAYBESTOS, AIMCO, AC DELCO, CARQUEST, BENDIX, AND WAGNER. ONLY PRODUCTS THAT WERE MANUFACTURED FROM JULY 27, 2005 THROUGH JANUARY 17, 2006 (DATE CODES 0529 THROUGH 0602) ARE SUBJECT TO THIS RECALL. WHEN SUBJECT TO VERY COLD TEMPERATURES, AN INTERNAL SEAL IN THE MASTER CYLINDER COULD LOSE FLEXIBILITY AND MAY CAUSE BRAKE FLUID TO LEAK.

VEHICLE DESCRIPTION: PASSENGER VEHICLES BUILT AT THE KANSAS CITY ASSEMBLY PLANT AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN, AND THE DISTRICT OF COLUMBIA. THE FRONT COIL SPRINGS MAY FRACTURE AS A RESULT OF CORROSION IN HIGH CORROSION ENVIRONMENTS. DEPENDING ON THE LOCATION OF THE FRACTURE, A BROKEN SPRING COULD MOVE PAST THE SPRING SEAT AND CONTACT A FRONT TIRE.

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1998 FORD CONTOUR/MERCURY MYSTIQUE PASSENGER VEHICLES BUILT AT THE KANSAS CITY ASSEMBLY PLANT. THE FRONT COIL SPRINGS COULD POTENTIALLY FRACTURE DUE TO CORROSION.

ON CERTAIN MY 1996-1998 PASSENGER VEHICLES BUILT AT THE KANSAS CITY, CUAUTITLAN ASSEMBLY PLANTS OR ON MY 1999 PASSENGER VEHCLES BUILT AT THE AUTOMOTIVE ALLIANCE INTERNATIONAL ASSEMBLY PLANTS, THE ROUGH SURFACE OF THE HEATER BLOWER RESISTOR'S STAINLESS STEEL BLADES CAN DAMAGE THE COPPER SURFACE OF THE WIRING HARNESS CONNECTOR. THE DAMAGE COULD, OVER TIME, CAUSE INCREASED RESISTANCE IN THE CONNECTOR AND, DUE TO SUBSEQUENT TERMINAL RELAXATION, RESULT IN AN OPEN CIRCUIT CONDITION.

VEHICLE DESCRIPTION: BI-FUEL VEHICLES. THESE VEHICLES MAY HAVE A FUEL TANK FILLER PIPE GROMMET THAT COULD HAVE BEEN DAMAGED DURING THE INSTALLATION OF THE BI-FUEL SYSTEM. IF THE GROMMET IS DAMAGED, FUEL COULD LEAK. FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE. DEALERS WILL REPLACE THE FUEL TANK FILLER PIPE GROMMET.

VEHICLE DESCRIPTION: PASSENGER VEHICLES NOT EQUIPPED WITH THE ANTI-LOCK BRAKING SYSTEM (ABS). A PRESSURE CONSCIOUS REDUCING VALVE (PCRV) IN THE REAR BRAKES MAY BE SUBJECT TO CORROSION AND RESULT IN MALFUNCTION, WHEN OPERATED IN AREAS THAT USE SALT COMPOUNDS ON THE ROADWAY FOR DE-ICING OR DUST CONTROL.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG SENSOR WIRING PIGTAIL INSULATION CAN BECOME BRITTLE AND CRACK OVER TIME DUE TO ACCUMULATION OF WATER IN THE PIGTAIL PROTECTIVE CONVOLUTE IN COMBINATION WITH HIGH UNDERHOOD TEMPERATURES RELATED TO THE ROUTING OF THE WIRING PIGTAIL NEAR THE RADIATOR. THIS CAN RESULT IN ENVIRONMENTAL STRESS CRACKING OF THE INSULATION.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE ACCELERATOR CABLE MAY HAVE BEEN MANUFACTURED WITH A BURR ON OR NEAR THE END OF THE CABLE SLEEVE INTERIOR. THIS BURR COULD FRAY THE CORE WIRE RESULTING IN THE ACCELERATOR NOT RETURNING TO IDLE WHEN THE ACCELERATOR IS RELEASED.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TERMINALS AT THE HEADLIGHT SWITCH AND WIRING HARNESS CONNECTOR CAN EXPERIENCE HEAT DAMAGE AS A RESULT OF OVERHEATING.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE FLOOR SHIFT AUTOMATIC TRANSMISSION CONTROL CAN BE DAMAGED IF SUBJECTED TO CERTAIN INTERIOR CLEANING PRODUCTS. THE GEAR POSITION INDICATOR CAN DETERIORATE AND NOT CORRECTLY INDICATE THE ACTUAL GEAR POSITION.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TEXT AND/OR GRAPHICS FOR THE VEHICLE HEADLAMP AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."